Warning: Required memory type for device not found. Assuming MEMF_24BITDMA. SCSIQuery 1.34 (15.12.2018) © THOR Generic sense data : Test unit ready returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Device inquiry data : Device status : connected. Device class : direct access device. Fixed medium device. Device type modifier : 00. ISO version : 00. ECMA version : 00. ANSI version : unknown ANSI version 3. Response data format : SCSI-2. Additional data length 5B. Flags: Relative addressing not supported. 32 bit wide SCSI not supported. 16 bit wide SCSI supported. Synchron data transfer supported. Linked commands supported. Tagged queues supported. Device reacts with hard reset. Vendor : QUANTUM Product : ATLAS10K3_73_WLS Version : 020W Date : 34821925 Comment : 15630000!2 Extended inquiry data : 0C 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 00 00 00 00 00 ........ 00 00 00 ... Control page information: Mode Data Length : 229 Medium Type : 0 Device specific : 144 Block des. len : 8 Density code : 0x8 Number of Blocks : 9448464 Block Length : 512 Page code : 0x01 (Page can be saved in non-volatile memory) Page length : 10 Read write error recovery page: *Automatic write reallocation enabled. *Automatic read reallocation enabled. Do not return defective block to initiator. Tolerate delays to correct erraneous data. Use safest data correction first. Do not report recovered errors. Don't terminate data phase upon detection of recovered errors. Do not use error correction codes. Read retry count : 4 Data correction span : 170 bits Head offset count : 0 Strobe offset count : 0 Write retry count : 8 Recovery time limit : 0 ms Page code : 0x02 (Page can be saved in non-volatile memory) Page length : 14 Disconnect reconnect page: Buffer full ratio : 0 % Buffer empty ratio : 0 % Bus inactivity limit : 0 µs Disconnect time limit : 0 µs Connect time limit : 0 µs Maximum burst size : 0 bytes Disconnect control is not used. Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 579 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x04 (Page can be saved in non-volatile memory) Page length : 22 Rigid disk parameter page: Number of cylinders : 31022 Number of heads : 8 Start precompensation at cyl. : 31022 Start reduced write at cyl. : 0 Step rate : 0 ns Landing zone : 31022 Spindle synchronization unsupported. Rotational offset : 0 Rotation rate : 10021 rpm Page code : 0x07 (Page can be saved in non-volatile memory) Page length : 10 Verify error recovery page: Tolerate delays to correct erraneous data. Use safest data correction first. Do not report recovered errors. Don't terminate data phase upon detection of recovered errors. Do not use error correction codes. Verify retry count : 4 Verify correction count : 170 bits Verify recovery time limit : 0 ms Page code : 0x08 (Page can be saved in non-volatile memory) Page length : 18 Cache control page: *Return GOOD after receiving but before writing data to disk. Prefetch data is absolute. READ cache utilized. Demand READ priority : Cache and medium have the same priority. Demand WRITE priority : Cache and medium have the same priority. Prefetch disable treshhold : 65535 blocks Minimum prefetch : 0 blocks/factor Maximum prefetch : 1497 blocks/factor Maximum prefetch ceiling : 1497 blocks Page code : 0x0A (Page can be saved in non-volatile memory) Page length : 10 Device control page: Do not report log exceptions. Queue algorithm : Unrestricted reordering. Resume queued I/O processes on error. Allow tagged queuing. Extended contingent allegiance disabled. Ready AEN permission disabled. Unit attention AEN permission disabled. Error AEN permission disabled. Ready AEN holdoff period : 0 ms Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 0 Starting boundary : cylinder 0 head 0 Ending boundary : cylinder 31021 head 7 Notch depended pages mask : 0x0000000000001008 Page code : 0x10 (Page can be saved in non-volatile memory) Page length : 22 Device configuration page: No partition change specified. No active format change specified. Active format : 2 Active partition : 0 Write buffer full ratio : 0 % Write buffer empty ratio : 0 % Write delay time : 25600 ms RECOVER BUFFERED DATA command not supported. Block IDs not supported. Ignore setmarks. Select drive default speed. Pre read data until buffer is full, ignore filemarks. RECOVERED BUFFERED DATA sent in FIFO order. Do not report early warning. Gap size : 0 EOD format : Unit default EOD definition. EOD generation disabled. Retain unwritten data in buffer at early warning. Buffer size at early warning : 0 bytes Data compression algorithm : 0 Page code : 0x1A (Page can be saved in non-volatile memory) Page length : 10 Power Condition Page: Drive may not enter the idle condition. Drive may not enter the standby condition. Idle condition timer : 0 ms. Standby condition timer : 0 ms. Page code : 0x1C (Page can be saved in non-volatile memory) Page length : 10 Printing RAW page data: 90 04 00 00 00 00 00 00 ........ 00 01 .. Page code : 0x39 (Page can be saved in non-volatile memory) Page length : 20 Printing RAW page data: 0C 00 07 00 00 28 00 00 .....(.. 02 22 05 03 05 01 00 00 ."...... 00 00 3C 0A ..<. Page code : 0x00 (Page can be saved in non-volatile memory) Page length : 2 Operating Parameters Page: Write verify enabled. Reset status report enabled. Drive operates as removable cartridge drive. Sufficient spare sectors available. Software write protect disabled. Audible eject notification disabled. Write verify enabled, bit 0. Device type qualifier : 00 Parameters for notch 1: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 686 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 1 Starting boundary : cylinder 0 head 0 Ending boundary : cylinder 1288 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 2: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 686 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 2 Starting boundary : cylinder 1289 head 0 Ending boundary : cylinder 2576 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 3: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 686 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 3 Starting boundary : cylinder 2577 head 0 Ending boundary : cylinder 3872 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 4: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 686 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 4 Starting boundary : cylinder 3873 head 0 Ending boundary : cylinder 5168 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 5: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 686 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 5 Starting boundary : cylinder 5169 head 0 Ending boundary : cylinder 6456 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 6: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 676 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 6 Starting boundary : cylinder 6457 head 0 Ending boundary : cylinder 7752 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 7: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 660 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 7 Starting boundary : cylinder 7753 head 0 Ending boundary : cylinder 9040 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 8: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 660 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 8 Starting boundary : cylinder 9041 head 0 Ending boundary : cylinder 10336 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 9: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 660 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 9 Starting boundary : cylinder 10337 head 0 Ending boundary : cylinder 11632 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 10: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 638 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 10 Starting boundary : cylinder 11633 head 0 Ending boundary : cylinder 12920 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 11: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 620 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 11 Starting boundary : cylinder 12921 head 0 Ending boundary : cylinder 14216 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 12: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 603 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 12 Starting boundary : cylinder 14217 head 0 Ending boundary : cylinder 15512 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 13: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 584 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 13 Starting boundary : cylinder 15513 head 0 Ending boundary : cylinder 16800 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 14: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 572 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 14 Starting boundary : cylinder 16801 head 0 Ending boundary : cylinder 18096 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 15: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 554 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 15 Starting boundary : cylinder 18097 head 0 Ending boundary : cylinder 19384 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 16: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 542 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 16 Starting boundary : cylinder 19385 head 0 Ending boundary : cylinder 20680 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 17: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 528 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 17 Starting boundary : cylinder 20681 head 0 Ending boundary : cylinder 21976 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 18: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 509 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 18 Starting boundary : cylinder 21977 head 0 Ending boundary : cylinder 23264 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 19: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 495 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 19 Starting boundary : cylinder 23265 head 0 Ending boundary : cylinder 24560 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 20: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 471 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 20 Starting boundary : cylinder 24561 head 0 Ending boundary : cylinder 25856 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 21: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 452 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 21 Starting boundary : cylinder 25857 head 0 Ending boundary : cylinder 27144 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 22: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 440 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 22 Starting boundary : cylinder 27145 head 0 Ending boundary : cylinder 28440 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 23: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 336 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 418 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 23 Starting boundary : cylinder 28441 head 0 Ending boundary : cylinder 29728 head 7 Notch depended pages mask : 0x0000000000001008 Parameters for notch 24: Page code : 0x03 (Page cannot be saved) Page length : 22 Device format page: Tracks per zone : 8 Spare zone sectors per zone : 65535 Spare tracks per zone : 0 Spare tracks per LUN : 83 Sectors per tracks : 396 Bytes per sector : 512 Interleave : 1 Track skew factor : 25 Cylinder skew factor : 23 Soft sector formatting not supported. *Hard sector formatting supported. Removable media not supported. Allocate tracks from the same cylinder first. Page code : 0x0C (Page can be saved in non-volatile memory) Page length : 22 Notch page: *Device is notched. Notch boundaries based on physical blocks. Maximum number of notches : 24 Active notch : 24 Starting boundary : cylinder 29729 head 0 Ending boundary : cylinder 31021 head 7 Notch depended pages mask : 0x0000000000001008 Device capacity : Capacity in blocks : 143666192. Block length : 512. Blocks from start up to a substiantial delay : Number of blocks : 686. Primary defect list: Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Grown defect list: Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header returned error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00. Read Defect List Header error : Check Condition : Details as below. LBA not valid. Error code of last command. Segment ID : 00. SenseFlags : Sense Key : Medium error. Additional sense length : 10. Cmd information bytes : 00 00 00 00. Drive specific flags : Extended sense code ASC : 0x19. Extended sense code ASCQ: 0x03. ASC,ASCQ encoded error is defect list error in grown list. Field replaceable unit code FRUC 0x00. Additional flags : Error data output. Byte error. Bit position 0x00. Byte position : 0x00 0x00.